BIM技术在铁路预应力混凝土连续梁零号节段深化设计中的应用

近年来,部分铁路预应力混凝土连续梁支座附近出现浇筑不密实、蜂窝麻面等问题,一定程度上影响了连续梁质量。针对这一现状,结合BIM及C#语言技术,从深化设计平台的选择、精细化模型的构建以及BIM技术在深化设计中的应用开展研究。结果表明:(1)通过合理拆分并在空间上进行布尔组合,能够较快构建铁路连续梁零号节段BIM模型,满足深化设计条件;(2)基于BIM模型开展深化设计、生成2D图纸并统计工程数量,能够直观发现设计中的不足,一定程度上提升设计质量和效率。     

基于铁路通信光缆维护要点分析与故障处理探究

主要对铁路通信光缆维护工作要点进行阐述,并积极探讨出具体的故障处理措施,希望能够对日常维护工作起到一定的参考作用。     

Integrated design optimization of spar floating wind turbines

A linearized aero-hydro-servo-elastic floating wind turbine model is presented and used to perform integrated design optimization of the platform, tower, mooring system, and blade-pitch controller for a 10 MW spar floating wind turbine. Optimal design solutions are found using gradient-based optimization with analytic derivatives, considering both fatigue and extreme response constraints, where the objective function is a weighted combination of system cost and power quality. Optimization results show that local minima exist both in the soft-stiff and stiff-stiff range for the first tower bending mode and that a stiff-stiff tower design is needed to reach a solution that satisfies the fatigue constraints. The optimized platform has a relatively small diameter in the wave zone to limit the wave loads on the structure and an hourglass shape far below the waterline. The shape increases the restoring moment and natural frequency in pitch, which leads to improved behaviour in the low-frequency range. The importance of integrated optimization is shown in the solutions for the tower and blade-pitch control system, which are clearly affected by the simultaneous design of the platform. State-of-the-art nonlinear time-domain analyses show that the linearized model is conservative in general, but reasonably accurate in capturing trends, suggesting that the presented methodology is suitable for preliminary integrated design calculations.     

高速磁浮车辆悬浮架装配关键技术研究

文章针对高速磁浮车辆悬浮架装配关键技术展开研究,通过悬浮架的功能与技术以及各结构模块组成关系对悬浮架进行分析,确定装配工艺流程、工艺重点与难点,实现了装配的技术要求。     

船检履约与应对IMO强制审核要点与措施研究

为促进全球海上安全和防污染相关国际公约的有效执行,国际海事组织于2009年批准了"IMO成员国自愿审核机制"强制化,我国将于2021年接受IMO的强制审核。船检占强制审核政府义务条款大部分内容,其被视为IMO进行强制审核的重点领域。因此,本文拟针对IMO履约规则及相关国际公约中有关船检的管理要求,对我国海事船检履约情况进行评估,分析我国船检海事立法与管理方面存在的问题,提出我国针对船检履约与应对IMO强制审核的要点及改进措施,以满足2021年IMO强制审核的要求。     

车用摇枕铸钢件浇冒口切割打磨自动化系统的设计

铸钢件毛坯浇冒口切割及打磨时存在噪音大、弧光强烈、粉尘污染严重,增加了人工操作时的劳动强度,并严重影响操作人员的身体健康。本文针对这些问题,拟以铁路车辆摇枕铸钢件浇冒口切割及打磨为例,提出了单工位打磨、流水线式多工位合作的打磨清理方案,设计了自动化打磨单元,实现机械化、自动化操作,既提高了铸件打磨清理的质量和生产率,又大大改善了工人操作条件,减轻了工人的劳动强度,达到了“以机代人”的目的,对铸钢件实现绿色化乃至智能化生产具有重要意义。     

Environmental lumping for efficient fatigue assessment of large-diameter monopile wind turbines

Fatigue damage is one of the governing factors for the design of offshore wind turbines. However, the full fatigue assessment is a time-consuming task. During the design process, the site-specific environmental parameters are usually condensed by a lumping process to reduce the computational effort. Preservation of fatigue damage during lumping requires an accurate consideration of the met-ocean climate and the dynamic response of the structure. Two lumping methods (time-domain and frequency-domain) have been evaluated for a monopile-based 10 MW offshore wind turbine, both based on damage-equivalent contour lines. Fatigue damage from lumped load cases was compared to full long-term fatigue assessment. The lumping methods had an accuracy of 94–98% for the total long-term fatigue damage and 90% for individual wind speed classes, for aligned wind and waves. Fatigue damage was preserved with the same accuracy levels for the whole support structure. A significant reduction of computational time (93%) was achieved compared to a full long-term fatigue assessment. For the cases with 30° and 60° wind-wave misalignment, there was a mean underestimation of approximately 10%. Variations in penetration depth did not affect the selection of the lumped sea-state parameters. This work presents a straightforward method for the selection of damage-equivalent lumped load cases, which can adequately preserve long-term fatigue damage throughout the support structure, providing considerable reduction of computational effort.     

双层带式输送机系统在散货码头上的应用

某些散货码头项目中,码头位置距离后方陆域较远,需要利用长距离带式输送机将物料从码头输送到后方。针对常规的水平运输方案会造成水工引桥宽度大、造价高的问题,探讨如何优化带式输送机布置形式,减少整个码头的建设成本。采用下层普通带式输送机和上层管状带式输送机的双层设计方案,在保证不同性质物料有效输送的前提下,可有效减小引桥宽度。实际运营检验证明双层带式输送机系统可安全可靠运行。     

柴油机增压器包覆层隔声性能试验分析及优化设计

提出一种船用增压器的包覆层结构,其内层为绝热材料和吸声材料,外层为金属薄片。采用统计能量法(SEA)建立该结构的中高频段隔声数值模型,开展包覆层的隔声试验,隔声量实测值与仿真结果吻合较好,能验证数值建模的有效性。对包覆层的吸声材料的厚度、密度和流阻等参数进行优化设计,利用正交试验法设计数值试验组,采用极差和方差分析法分析影响材料隔声性能的关键因素,得出最重要的影响因素是材料厚度,在选型设计中还应考虑密度和流阻因素。当安装厚度受限时,可通过改变密度和流阻值来提高材料的隔声量。     

基于ANSYS的无缆潜航器力学性能分析研究

为了设计无缆潜航器,采用数值分析和机械制造相结合的方式,设计出一款新型无缆潜航器,在设计制造出潜航器的基础上,对该无缆潜航器进行力学性能分析研究,对其水下运动规律及特性进行了理论推导,采用数值分析的方法分别讨论机器人的结构力学特性和流体力学特性,并对机器人的应力应变强度参数进行仿真分析,讨论不同情况下机器人的属性参数,结合分析数据,对潜航器运行工况下的各项参数进行了稳定性分析,最后对以上所有参数进行总结归纳,文中所采用的方法可以用于机器人设计及优化。